Blast Powercore gen4 eW, eColor

安装指示

PDF-000377-08 R04

2019十一月 15

必须根据所有国家和地方的电气和施工准则及规范,由符合资格的电工进行安装。
安装该产品之前,请先访问产品页面 www.colorkinetics.com 以获取最新版的安装说明。由于在不断地改进和创新,安装说 可能会有所改动,恕不另行通知。

  1. 确认收到了所有部件

垫片圈(已安装)
  1. 验证电气计划和所有必要的浪涌保护要求。

使用 Configuration Calculator 可帮助识别和定位所有照明器,Data Enabler Pro设备和控制器,并根据型号,线路电压,电路负载和电缆长度计算每个电路可支持的照明器数量。

只有精准的调光灯具

53.3 m 最大单线长度
122 m 最大总长度
  1. 只有精准的调光灯具 –记下各灯具的位置和序列号,以便查询

  1. 确保电源关闭

  2. (可选) 移开电缆

松开电缆固定支架

卸下电缆锁

  1. 连接灯具

通/断控制

精准的调光

线路电压

  1. 安装方案

平面(客户提供的硬件)

室内接线盒(#8–32 螺丝)

室外接线盒(#10–24 螺丝)

  1. 在潮湿的环境下,请密封所有入口 以防渗水。请使用灯具垫圈(提供)、 RTV 硅和防水接线盒

  1. 只有精准的调光灯具 - 连接引线电缆

有关特定安装和布线说明,请参阅数据启用程序专业安装说明
  1. 打开电源

  2. 只有精准的调光灯具 – 使用 QuickPlay Pro 软件配置各灯具

  3. 连接附件 (可选)

连接安装臂 (可选)

安装详细信息:请参阅 Mounting Arm Installation Instructions
  1. 对准灯具

切勿直视光束.
  1. 固定灯具

只能使用手动工具来锁定固定装置

先安装倾斜旋转螺丝(2.5 毫米)

扭矩设置为 2,82 N-m 英寸-磅

倾斜锁螺丝(5 毫米)

扭矩设置为 13,5 N-m 英寸-磅

  1. 连接安全电线

对灯具进行安装或接线前,需确保主电源已关闭。
阅读并理解安装说明和安全标签之前,切勿试图安装或使用灯
如果灯镜片、灯壳或电线受损,切勿使用产品。
灯具存在线电压电击的危险,且无用户可修理的部件。切勿试图打开产品。
切勿在任何非额定电压的情况下,使用产品。切勿超出灯具规定的电压与输入电流.
切勿热插拔产品。连接或断开单个灯具之前,必须确保供该系列之电源已关闭。
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer
This Class B digital apparatus complies with Canadian ICES-005. Cet appareil numerique de la classe B est conforme a la norme NMB-005 du Canada.
220V条件下功率因数≥0.90, 最大电流0.25A.

© 2019 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed.

www.colorkinetics.com


How did we do?


Powered by HelpDocs