ColorBurst Compact Powercore, Landscape - RGB

Installation Instructions

PDF-000262-01 R03

15 November 2018

Must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations.
Before installing this product, please visit the product page at for the latest version of the installation instructions. Due to continuous improvements and innovations, installation instructions may change without notice.

  1. Confirm all components received

  1. Verify the electrical plan and all necessary surge protection requirements.

Important Surge Protection Requirement:
Use Configuration Calculator to help identify and locate all luminaires, Data Enabler Pro devices, and controllers and to calculate the number of luminaires each circuit can support based on model, line voltage, circuit load, and cable lengths.

Data Control Limits

53.3 m (175 ft) maximum individual length
122 m (400 ft) maximum total length
  1. Record location and serial number of each luminaire for addressing.

  1. Make sure power is OFF

  2. Connect luminaires

  1. Secure connections and covers

For wet or damp locations, seal all points of entry to prevent water infiltration. Use RTV silicone and weatherproof junction boxes.
  1. Connect the Leader Cable

Refer to Data Enabler Pro Installation Instructions for specific mounting and wiring instructions
  1. Turn the power ON.

  2. Address luminaires with QuickPlay Pro software

  3. Attach accessories (Optional)

  1. Aim luminaires

Do not look into beam.

Attach safety cable

Ensure that main power supply is off before installing or wiring a luminaire.
Do not attempt to install or use a luminaire until you read and understand the installation instructions and safety labels.
Do not use a luminaire if the lens, housing, or power cables are damaged.
Luminaires have line voltage risk of shock and no user serviceable parts. Do not attempt to open them.
Do not use a luminaire for any voltage for which it is not rated. Do not exceed the specified voltage and current input for any luminaire.
Do not hot swap luminaires. Ensure that power to the series is off before connecting or disconnecting individual luminaires.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense.
Warning - This is a Class A product. In a domestic environment this product may cause radio frequency interference in which case the user may be required to take adequate measures.
This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
产品在 220V条件下,额定输入电流最大为0.17A,功率因素大于或等于0.9
The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire shall be destroyed. 此灯具的外部软缆或软线不能替换;如果软线损坏,该灯具即应报废
The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person. 此灯具内的光源应由制造商或其服务代理商或有类似资格的人来更换。

© 2019 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. All trademarks are owned by Signify Holding or their respective owners.

How Did We Do?

Powered by HelpDocs (opens in a new tab)